Monoprice 7537 IR 1000 Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Monoprice 7537 IR 1000. Monoprice 7537 IR 1000 User Manual [es] Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 1
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Hidden IR Repeater System
Model: IR 1000
Introduction
The Hidden IR Repeater System allows you to use an existing
infrared (IR) remote control to operate up to eight audio/video
(A/V) components located behind closed doors or walls in an
entertainment cabinet or equipment closet.
A/V Components
IR Receiver
Remote Control
IR Repeater Box
Plug-in Power Supply
Dual Output Emitters
Whats Includes:
• Hidden IR Repeater Box,
• Four (4) Dual Output Emitters with 2m & 4m cord and mini-plug
connector,
• IR Receiver with 1m cord and 4-pin DIN connector,
• Plug-in Power Supply.
Installation
1) Place the IR Repeater Box on a flat surface in your entertainment cabinet or equipment closet (secure with the included adhesive if
necessary)
a) The IR Repeater Box should be located within 2m or 4m of each A/V component (as this is the length of the Dual Output Emitter
cables)
2) Connect the 4-pin DIN connector from the IR Receiver to the IR Repeater Box, by inserting the plug into the 4-pin DIN port
3) Find a location where the IR Receiver can receive IR signals from your remote control(s) and remove the backing from the tape to the IR
Receiver to the surface; the “eye” is located in the tip of the IR Receiver and should be facing the area from which you will be using your
remote control(s)
a) Make sure the receiver is mounted at least one foot away from your television (to avoid interference) and no longer than 2m or 4m
from the IR Repeater Box (as this is the length of the IR Receiver cable)
b) Suggested mounting locations include: on a shelf, on an exposed part of an entertainment cabinet or behind a speaker grille
4) Connect the 1/8mini-plug connector from the Dual Output Emitter(s) to the IR Repeater Box, by inserting each Dual Output Emitter plug
into a 1/8” mini-plug port
5) Locate the IR “eye” of each A/V component you wish to control
a) If you can’t easily locate the eye, shine a light through the front panel of the component; the eye is a small red disc, approximately 1/8
in diameter
6) Once located, remove the backing from the emitter’s clear tape and attach each IR Emitter to the IR eyeof each A/V component to be
controlled
a) Please note that these are dual emitter cables; the cable splits in two, so two components can be controlled by each cable (four cables
included)
7) Insert the barrel plug end of the Plug-in Power Supply to the barrel plug port of the IR Repeater box and then insert the plug end into a
standard 110-240VAC outlet
8) Verify operation by turning your system components on using your existing IR remote controls
Using the Hidden IR
Aim your IR remote at the Hidden IR Receiver and use
the remote control as usual
The LED light on the IR Receiver will blink when you
use your remote control(s), confirming the system is
working properly
Notes
Some A/V components, such as high-powered amplifiers and
receivers, may require additional ventilation and will overheat
in an enclosed cabinet. Check the components manuals prior
to enclosing them fully.
Protect the IR receiver from plasma screens and devices that
emit too much low-frequency RF or an excess of ambient light,
including direct sunlight, floodlights, and some halogen or
fluorescent lamps
Avoid allowing IR emitter cables to block equipment doors
and slots that may need to be opened from time to time
Youll enjoy increased range in dimmer applications, as this
IR system has more sensitivity with less ambient light
If you prefer, attach an IR emitter to a shelf so that it is facing
the components IR eye and is within 3 inches of the eye.
This will allow IR control without attaching the IR emitter
directly to the component.
Do not attempt to open the power supply or IR repeater box.
Doing so will void your warranty
The Hidden IR is not weather-resistant. Do not expose this
system to moisture.
Vista de pagina 0
1

Indice de contenidos

Pagina 1 - Hidden IR Repeater System

Hidden IR Repeater System Model: IR 1000IntroductionThe Hidden IR Repeater System allows you to use an existing infrared (IR) remote control to operat

Comentarios a estos manuales

Sin comentarios